Academy
Generator Clearance Requirements: NFPA 37 vs CPSC 25 ft
Published · 10 min read
A contractor in New Jersey once told a homeowner the Generac diagram was all the code he needed. He set the unit 18 inches off the rear wall, exactly per Figure 3-2, and scheduled the inspection. It failed. The wall he measured to had a bathroom window in it, and the township applies NFPA 37’s five-foot opening rule regardless of what the fire-test listing does to the wall figure. The pad came out, the unit moved, and the permit was re-filed six weeks later than planned.
That mix-up is common enough to have a name among plans examiners: conflating the wall clearance with the opening clearance. It is one of at least four separate rulebooks that decide where a home standby generator is allowed to sit, and as of 2025 there is a fifth figure in circulation that most installers have not caught up with yet. This is what each one actually requires, where they disagree, and how to reconcile them before you pour concrete.
Four layers, and the strictest one governs
No single document tells you where a generator can go. Four separate sources each publish their own figure for the same physical distance, and building departments apply whichever one is strictest for each face of the enclosure:
| Layer | Who publishes it | Typically covers |
|---|---|---|
| Manufacturer listing | Generac, Cummins, Kohler, etc. | Structure, service access, overhead |
| Model fire code | NFPA 37 | Openings, combustible walls, intakes |
| Local ordinance | Your city, township or county | Property line, noise, permitted zones |
| CPSC recommendation | U.S. Consumer Product Safety Commission | Advisory only, not yet enforced |
What the manufacturer manual actually specifies
Installers often assume one clearance chart covers every brand. It does not, and the differences are large enough to fail an inspection if you copy one manufacturer’s diagram onto another manufacturer’s unit. Generac’s air-cooled family is symmetric enough that one rear figure covers the whole envelope. Cummins is not — its RS series states four different distances depending which side of the cabinet you are measuring from.
| Manufacturer / face | Minimum clearance | Source |
|---|---|---|
| Generac — rear wall | 18 in | Install. Guidelines, Fig. 3-2 |
| Generac — overhead | 5 ft | Install. Guidelines, Fig. 3-2 |
| Cummins — engine/alternator side | 18 in | A053X172, Issue 16 |
| Cummins — opposite side | 60 in | A053X172, Issue 16 |
| Cummins — intake side | 30 in | A053X172, Issue 16 |
| Kohler — combustibles, exhaust end | 4 ft | TP-6803 2/21q |
| Kohler — furnace/HVAC intakes | 10 ft | TP-6803 2/21q |
Kohler’s manual does not publish a numeric structure clearance at all — it defers to state and local codes and a dimensioned drawing, which is a gap worth knowing before you site one. Every figure above, with its verbatim source sentence, is set out on the methodology page.
None of these figures move with the kW rating. A 24 kW Cummins unit sits under the same clearance table as a 13 kW one — sizing changes the load calculation, the gas line and the pad, not the setback.
NFPA 37’s five-foot rule, and the reduction it doesn’t apply to
NFPA 37 §4.1.4 sets a five-foot minimum from an outdoor engine to both combustible walls and to openings in those walls. Where the confusion starts is that Generac’s enclosure was fire-tested by Southwest Research Institute, and that listing lets the wall figure drop to 18 inches. The listing says nothing about openings. A window, door, vent or window well within that same wall still needs the full five feet, and it is measured from any part of the generator, not from the nearest edge of the cabinet. Cummins states the identical 60-inch opening figure independently in its own manual, so this is not a Generac quirk — it is how the model code treats a fume path into an occupied structure differently from a fume path into open air.
The figure most installers haven’t caught up with: CPSC’s 25 feet
In June 2025 the Consumer Product Safety Commission published a report that changes the conversation, even though it changes no permit form. The study followed a wave of carbon monoxide poisonings across Southeast Louisiana after Hurricane Ida, and traced how exhaust from stationary generators reached indoor air in 105 separate homes, with symptomatic exposure recorded in twelve of them and nine residents sickened in a single household. The agency’s conclusion was blunt: it should never be assumed that CO from a stationary generator cannot infiltrate the home, and its new consumer guidance now recommends siting a stationary unit at least 25 feet away — five times NFPA 37’s figure.
“It’s one of the hazards that we’re becoming a lot more aware of.”
— Val Ziavras, NFPA engineer, on carbon monoxide risk from stationary generators
NFPA’s technical committee is now reviewing whether the standard itself should change, and Ziavras was clear that adoption is a local decision: every jurisdiction runs its own process for pulling a revised standard into enforceable law, on its own timetable. Nothing in this report has amended NFPA 37, and no permit application in our dataset currently asks for 25 feet. Treat it the way a good contractor treats any safety margin beyond the code minimum: aim for it when the lot allows, and don’t let it stop you meeting the figure that is actually enforceable today.
The stakes are not abstract. CPSC attributes roughly 85 to 100 consumer deaths a year to generator-related carbon monoxide poisoning, and portable and stationary units together account for around 40% of all CO deaths linked to consumer products since 2009. Demand for the equipment causing that exposure keeps climbing — outages lasting over an hour hit more than a quarter of U.S. households in a single recent year, and the residential standby market is on a trajectory of high single-digit to low double-digit annual growth through the early 2030s. More units are going in every season; the placement rules matter more, not less.
Where the local layer adds a requirement the code doesn’t
Zoning setbacks, noise limits and permitted zones are entirely local, and none of them come from NFPA 37. Four jurisdictions we have verified from primary source documents illustrate how differently they can bite:
| Jurisdiction | What it adds beyond the model code |
|---|---|
| Scarsdale, NY | Per-district lot-line setback (3–20 ft) plus a 70 dBA noise cap at 23 ft |
| Wall Township, NJ | Mandatory evergreen screening; ordinary zone setbacks apply, front yard barred |
| Pemberton Township, NJ | 5 ft minimum from the lot line, but capped at 15 ft maximum from the building served |
| Leon County, FL | 10 ft to openings (double NFPA 37) plus 120 mph wind-anchoring certification |
Pemberton’s combination is the one that catches people out: a five-foot minimum from the property line and a fifteen-foot maximum from the house being served can conflict outright on a narrow lot, and there is no way to resolve that from the manufacturer manual alone — it has to be walked on the actual site plan.
A five-step way to reconcile all of this before the pad goes down
- Pull the manufacturer’s clearance figure for every face of the enclosure — rear, front, both ends and overhead — not just the one your installer quotes from memory.
- Check whether that figure is a listing-reduced number (like Generac’s 18 in) and confirm your local authority accepts the listing before relying on it.
- Apply NFPA 37’s five-foot opening rule separately from the wall rule — it does not shrink just because the wall figure did.
- Look up your specific jurisdiction’s ordinance for lot-line, noise and permitted-zone rules; assume nothing carries over from a neighbouring town.
- Site toward, but don’t force, the CPSC’s 25 ft distance from every occupied structure — yours and the neighbour’s — wherever the lot has the room.
That is the exact reconciliation SetbackCalc runs automatically: pick the unit and the jurisdiction, and it returns the governing figure for each face with every superseded figure shown alongside it and the source sentence behind the number. Doing more than one address at a time — a builder with several lots on the same permit cycle — is what the batch mode and the JSON API exist for.
Frequently asked questions
Does the CPSC's 25-foot recommendation replace the 5-foot NFPA 37 rule?
No. The CPSC's June 2025 report is a hazard-mitigation recommendation aimed at consumers and policymakers, not an amendment to NFPA 37 or to any adopted building code. The 5 ft (or the reduced 18 in listing figure) is still what a plans examiner checks a permit application against today. NFPA's own technical committee has said it is reviewing the finding, which is the normal first step before a code change — not a sign that 25 ft is enforceable yet. Until a jurisdiction actually adopts a longer distance, treat the CPSC figure as the safer target when the lot allows it, not as the permit requirement.
What if my lot is too small to fit 25 feet from the house?
Most suburban lots are. The CPSC's own study came out of dense post-storm New Orleans housing, where 25 ft from every structure is rarely achievable either. Where you cannot meet the aspirational distance, meeting the enforceable one — the manufacturer's listing, the model code and your local ordinance, whichever is strictest for each face — plus siting the exhaust to point away from every window, door and eave vent, and away from a neighbouring property's openings too, does the most good with the space available.
My permit only asks for one clearance figure. Why does SetbackCalc show several?
Because a permit application usually only asks you to state the manufacturer's figure, but the plans examiner is entitled to apply model code and local ordinance figures on top of it — and will, if your placement fails inspection. Showing the manufacturer, NFPA 37 and local figures side by side, with the strictest one flagged as governing, is how you catch a conflict before the inspector does rather than after the pad is poured.
Do I need an engineer to certify generator placement?
Only where a specific requirement triggers it — most commonly a wind-resistance or anchoring requirement that the manufacturer's installation instructions do not already specify a method for. Leon County, FL is the clearest example in our dataset: FBC Residential §M1905.2.4 requires anchoring rated to a 120 mph minimum design wind speed, and where the manufacturer's instructions are silent on the anchoring method, a Florida-licensed engineer has to certify it. Clearance distances themselves are not an engineering calculation — they are read directly off the manufacturer manual, the model code and the local ordinance.
For the full dataset — every clearance figure across all three manufacturer families and all four jurisdictions, each with its verbatim source quote — see the methodology. To generate a stamped-ready placement schedule for a permit pack, the Pro plan removes the watermark from the PDF export.
Sources: CPSC, Stationary Generators: The Carbon Monoxide Poisoning Hazard and Recommendations for Mitigation (June 2025); Fox 8 WVUE, “New federal warning: Keep generators 25 feet from homes” (October 2025); InvestigateTV, “Generator carbon monoxide dangers: Federal report calls new safety-distance rules” (February 2026); NFPA, NFPA 37 standard development; and GMI, Home Standby Gensets Market Size & Forecast. This article is a design aid, not a substitute for the authority having jurisdiction.