Manufacturer listing · NFPA 37 · Local ordinance
Where can the generator actually go? Three rulebooks disagree. This tells you which one wins.
Pick the unit and the jurisdiction. Get the governing clearance for every face of the enclosure — the strictest of the manufacturer’s listing, NFPA 37 and the local code — with the figures it beat shown alongside it and the verbatim source sentence behind each one, so a plans examiner can check it rather than trust it.
The trap this exists for: the fire-test listing that lets a Generac sit 18 in from a wall does not reduce the 5 ft required to openings in that wall — and in Florida it is 10 ft, not 5. A placement drawn correctly off the manufacturer diagram can still fail inspection.
Frequently asked questions
What are the clearance requirements for a home standby generator?
For a Generac air-cooled unit the manufacturer's Figure 3-2 gives 18 in at the rear from an existing wall, 3 ft at the front and ends, and 5 ft overhead from any structure, overhang or projection. Separately, NFPA 37 §4.1.4 requires 5 ft from openings in walls and 5 ft from structures having combustible walls. The 18 in rear figure is a reduction from that 5 ft, allowed because Southwest Research Institute fire-tested the enclosure — and your local authority can decline it. SetbackCalc shows you both figures and which one governs.
How far does a generator have to be from a window or door?
5 ft (60 in) under NFPA 37 §4.1.4, measured from any part of the generator to any operable window, door, vent or window well. Cummins states the same 60 in in its RS installation manual. This is the figure people most often get wrong, because they assume the 18 in listing reduction applies here too. It does not — the reduction is for the distance to the wall, not to openings in it. And in Florida it is not 5 ft at all: see below.
Why does Florida require 10 feet instead of 5?
Florida Building Code, Residential §M1905.2.5 requires generator exhaust termination to be a minimum of 10 ft from any opening that could allow fumes into the building, including doors, operable windows and eave vents. That is double the NFPA 37 figure and stricter than every manufacturer diagram in our dataset. The section publishes an exception allowing 5 ft (or the manufacturer's figure if more restrictive) where carbon monoxide alarms are installed within 10 ft of each sleeping room and additionally as close as possible to the exterior opening nearest the exhaust. A placement drawn correctly off a Generac diagram still fails Florida Building Control if you miss this.
Do generator clearances change with the kW rating?
Not in any family we have read. Generac publishes one clearance set covering its whole 9–22 kW air-cooled range; Cummins publishes one set for RS13A through RS20AC; Kohler publishes one for 14RESA through 20RESCL. Sizing the generator changes the load calculation, the gas supply and the pad footprint — not these distances. Anyone quoting you a clearance 'for a 22 kW' as though it differed from the 14 kW figure is inventing a dependency the manuals do not have.
Are Generac and Cummins clearances the same?
No, and this is a real trap. Generac states one rear figure around a broadly symmetric envelope. Cummins states four different per-face figures: one engine/alternator side at not less than 18 in from a combustible wall, the opposite side at not less than 60 in, the cooling air intake side at not less than 30 in, and the air discharge side at not less than 60 in with 36 in free of combustibles. A Cummins set positioned to a Generac diagram can be non-compliant on three sides at once.
What is the generator setback from the property line?
That is zoning, not fire code, and it is entirely local. Scarsdale NY, for example, publishes a per-district schedule: 15 ft rear and 20 ft side in Residence AA-1, down to 3 ft on both in A-4 and A-5. Pemberton Township NJ requires 5 ft from any property line and additionally caps the distance at 15 ft from the building served. Wall Township NJ publishes no generator-specific figure and applies the ordinary yard setbacks for the zone. There is no national number, which is why SetbackCalc only answers this for jurisdictions where we hold the verified document.
Which jurisdictions does SetbackCalc cover?
Four, verified from primary documents: Village of Scarsdale NY, Township of Wall NJ, Pemberton Township NJ, and Leon County FL (which reproduces Florida Building Code Residential §M1905 verbatim). That is a deliberately small, real dataset rather than a coverage claim we cannot back. For anywhere else the tool gives you the manufacturer and model-code layers and tells you plainly that the local layer is missing.
Can I put a standby generator under a deck?
Generac's installation guidelines say plainly: 'DO NOT install under wooden decks or structures', and require 5 ft minimum overhead clearance from any structure, overhang or projection from a wall. If you are placing a unit on a deck, roof or platform rather than under one, a different code section applies — NFPA 37 §4.1.3 — which permits 18 in from combustible walls and 5 ft from operable openings, and requires the surface beneath and beyond the unit to be non-combustible for at least 12 in.
How far must a generator be from an air conditioner or furnace intake?
10 ft. Generac's guidelines state that mechanical and gravity outdoor air intake openings for HVAC supply air systems must be not less than 10 ft horizontally from the generator enclosure, referring to Section 401 of the ICC Mechanical Code. Kohler states the same 10 ft for furnace and similar intakes, measured from the exhaust end. A powered intake is treated separately from a passive opening because it actively draws air inward.
Does my HOA affect where the generator goes?
Very possibly, and we cannot tell you. There is no public per-address source for CC&Rs, so SetbackCalc does not pretend to have one. HOA covenants routinely impose screening, placement and noise terms stricter than any code figure, and they are enforceable against you independently of the building permit. Read your CC&Rs and get architectural-review approval in writing before the pad is poured.
Do I need a permit to install a standby generator?
Almost always, and usually more than one. Leon County FL, for example, requires the generator model and kW rating, a load calculation to NEC Article 220 and 702.4, an electrical riser diagram, transfer switch details, a fuel gas riser, a site plan showing every adjacent opening with the clearances illustrated, plus flood elevation certification where applicable and wind-resistance certification by a Florida-licensed engineer where the manufacturer does not specify the anchoring method. Scarsdale NY requires an application with the manufacturer's sound specification before installation.
Is there a noise limit on a home standby generator?
In some jurisdictions, yes, and it can decide the placement. Scarsdale NY caps permanent standby generators at 70 dBA measured 23 ft from the unit, tightening to 66 dBA where the unit sits in the side yard in the A-3, A-4 and A-5 districts, and requires the manufacturer's sound specification with the permit application. Check your model's published sound level before committing to a side-yard position.
Every figure, its source quote, and an honest statement of what is not covered are set out in the methodology.